Dual La2a - [silent:arts] version

This section is for registered users to discussspecific projects and troubleshooting.

Moderator: kubi

Postby [silent:arts] » Fri Jan 18, 2008 6:18 pm

[silent:arts] wrote:since Frau Müller doesn't mark the beginning and end of secondary windings you have to measure it :o

sorry, I'm wrong. I've mistaken the two Heater windings with the 250V windings :oops:
(I measured the heaters to have them in phase, but this is not necessary)

just wire it like this:
Image
Last edited by [silent:arts] on Fri Feb 11, 2011 7:26 am, edited 1 time in total.
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

Postby waldorfcave » Fri Jan 18, 2008 6:22 pm

gracias amigo :P
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby waldorfcave » Fri Jan 25, 2008 5:10 pm

...so i just started wireing the unit, and i have some questions for the hook up of the switches and pots :?:

- the "LIMIT/COMP" switch when it is open Comp or Limit :?:

- the "GAIN RED" is this the switch for the vu-meter mode :?:
when it is open displays the vu Output or Gain Red :?:

- How should i connect the PeakReduction and GainPot :?:

love LArs
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby [silent:arts] » Fri Jan 25, 2008 5:25 pm

- "LIMIT/COMP": open = limit, closed = comp. haven't used it yet, and haven't seen much difference in the compression curve while meassuring

- "GAIN RED" is the gain reduction meter output. there is aother 2pole Molex next to the output cap behind the relay. this is the VU output. wire both to a 2pole switch, go from the switch to the VU Meters and don't forget to put one 3K9 resistor before the meter.

the gain and peak reduction potentiometers are connected one to one.
pin 1 on the Molex is GND, as it is at the potentiometer.
Last edited by [silent:arts] on Fri Jan 25, 2008 6:05 pm, edited 1 time in total.
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

Postby [silent:arts] » Fri Jan 25, 2008 6:05 pm

and if you use sowter output transformers:

I have had problems with gain over "7" (may be this grid stopper thing), but I changed the gain pot to a 22K log in series with a 75K resistor to get an easier to adjust gain range (still 26dB gain - enough for a compressor / limiter).
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

Postby waldorfcave » Fri Jan 25, 2008 6:48 pm

...fuck my tube are not lightning :cry:

i have no heater voltage. the trafo brings 7 AC but somewhere it disapeares.

the neon lamp shines
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby waldorfcave » Fri Jan 25, 2008 7:27 pm

maybe i´m stupid but the heater voltage goes after the 100r resistors straight to ground?

can someone tell me where i can measure the next spot where the hv is?
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby [silent:arts] » Fri Jan 25, 2008 7:43 pm

Yes, the heater goes to ground via the 100r (but you used the holes right after the terminal block, before the 100r resistors ?)
or wait, maybe you did not know you have to wire the heaters like in Drips v1 ?

should look something like this, or better (the silicon cable I used is not good drilled together:
Image

Take the tubes out and measure each heater terminal block input to ground if you actually have 100r. the PCB Billex made for me had a short at one side to ground (I checked the PCB Bernd send me for this, and it was right - but you never know).
[edit: with no power transformer connected of course]

the neon lamp is on the HV rail, if it shines it has more than 65V - that's good.

the best place to measure the HV (High Voltage) is the left side (looking from the front) of R129 or R229.
Last edited by [silent:arts] on Fri Feb 11, 2011 7:23 am, edited 3 times in total.
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

Postby bernbrue » Fri Jan 25, 2008 7:48 pm

Hi,
Heater voltage is AC and after a closer look to the solder side of the pcb it seems, that the heaters (H1L, H2L, H1R, H2R) have to be wired by hand. Is that right Volker?
regards
Bernd
User avatar
bernbrue
 
Posts: 1125
Joined: Thu Jun 29, 2006 2:55 pm
Location: Wolfenbüttel

Postby bernbrue » Fri Jan 25, 2008 7:50 pm

Volker, you are too fast :lol:
User avatar
bernbrue
 
Posts: 1125
Joined: Thu Jun 29, 2006 2:55 pm
Location: Wolfenbüttel

Postby waldorfcave » Fri Jan 25, 2008 7:51 pm

damm, sure now erverything is clear :P
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby [silent:arts] » Fri Jan 25, 2008 7:54 pm

:D I hate this undocumented projects :lol:
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

Postby waldorfcave » Fri Jan 25, 2008 8:30 pm

yes volker you are the man :P

after all my questions this projekt is very well documented :roll:


thx
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby waldorfcave » Sat Jan 26, 2008 2:03 pm

ok...this thing is running and compressing. :lol:

gain ratio have to be tuned like volker said (i use sowters) i do it later....

one problem is, that my unit hums a bit. more then it is ok for me :-(

it comes not from the powertransformer, i can move it from side to side and nothing happens.

maybe the ac heaters under the pcb?

i have measured the heater against ground, and i only have around 60 ohms
resistance between ground, but volker said it have to 100R?

maybe this is the fault?

maybe someone has an idea where to look first....

i will try and try :P
User avatar
waldorfcave
 
Posts: 265
Joined: Sat Jun 03, 2006 4:26 pm
Location: Kölle

Postby [silent:arts] » Sat Jan 26, 2008 2:09 pm

mhm, no hum here.
is it on both channels ?
can you do a photo of your ground pattern ?
volker
olafmatt wrote:Strom kann tot machen
[silent:arts]
 
Posts: 3481
Joined: Sat Jun 10, 2006 3:54 pm
Location: BLN

PreviousNext

Return to DIY Projects

Who is online

Users browsing this forum: No registered users and 2 guests

cron